Originally for St Mary's church (West Sussex) youth group's radio control yacht building and racing project
Monday, 25 July 2011
A very short maiden voyage!
I'm very glad I didn't take my son's advice bcz it had a bad leak behind one of the paddle wheels and would have sunk! That's why it was listing so badly. Is {hopefully) fixed now and other wise every thing went to plan, my unconventional twin rudders work well too! It a shame for the video that the top deck lid wasn't down fully.
Sunday, 24 July 2011
99% there.
Saturday, 9 July 2011
Testing my speed controller.
Testing my built from junk speed controller. That LM338 voltage regulator runs very hot though as it is dissipating too much power, I will try to find a battery closer to the 8 volts or so I actually need rather than the 13 volt one I have at the moment. I guess I could water cool it! But it proves it all works!
From left to right: Direction change micro switch-Servo-Speed potentiometer- Push to break power micro switch -direction change relay.
That hand drill bevel gear drive is a little noisy but that's all part of my boat's old school-low tech charm I guess!
Just added this video!
From left to right: Direction change micro switch-Servo-Speed potentiometer- Push to break power micro switch -direction change relay.
That hand drill bevel gear drive is a little noisy but that's all part of my boat's old school-low tech charm I guess!
Just added this video!
Friday, 1 July 2011
Progress!
As you can see I've started to build up the superstructure, to prevent it getting too top heavy it is mainly made from balsa, I have since these photos glued on the splashers and filled in the gap at the top. (and all the gaps where parts don't quite fit!) The battery was nearly flat so quite convenient for a test in the bath, I didn't want full power just a cruising speed and even like this it seemed impressive! The speed regulator board (LM338 chip) has just been tested on my bench and I will try it on the boat's motor tonight, now I need a 12 volt relay for reverse switching and and probably a second micro switch so that the motor is totally disconnected and not draining the battery when in the stop position. The main job left is designing and fitting the twin rudders that sit behind each paddle wheel, this seems far more sensible than one rudder trailing behind in the center where it would have far less influence and be more likely to be damaged.
Btw the doors came from the original aircraft carrier though they weren't doors, kind of louvers of some sort,I turned them round to show the back just bcz i thought they looked like a ships doors, probably more water tight and ocean going than you'd find on a river boat but never mind. I'm also going to use the aircraft lift platform as the bridge's roof as it has a nice planking pattern on it, why not.



Btw the doors came from the original aircraft carrier though they weren't doors, kind of louvers of some sort,I turned them round to show the back just bcz i thought they looked like a ships doors, probably more water tight and ocean going than you'd find on a river boat but never mind. I'm also going to use the aircraft lift platform as the bridge's roof as it has a nice planking pattern on it, why not.



Thursday, 23 June 2011
Less aircraft carrier and little more like a paddle steamer.
There seems to be a rather large paddle boat appearing on my bench! I Didn't realize it would turn out this big! Ok you still need to use some imagination as nothing is properly attached and my materials are rather unconventional ; Cut down paint pot spashers and decks from an old plastic phone book stand! Better float it again and recheck it's buoyancy! Btw I think I will cut off the last section of bow and fix a wooden block there so I can shape it how I want.
Thursday, 16 June 2011
Paddle Steamer Progress
I'm sure Isambard Kingdom Brunel floated a model of the Great Eastern in his bath just to check it's buoyancy...didn't he? The 12 volt electric motor is from a soviet made Lada car and it has been mated to cut down electric screwdriver gearbox (with metal epicyclical/planetary gears no less!) and then through the bevel gears of a hand drill, it has been tested and works beautifully, it needs installing for propper into the boat now so I need to fit wooden bearers into the hull so I can screw down the parts. Btw I'm not sure how much it will end up looking like a Murray river steamer! I've got some ideas of my own i want to try out.
Parts used in the drive train so far;
12 volt car windscreen washer motor (USSR made)
Radio knob for motor to geabox shaft coupling
Half an eletric scredriver gearbox
Electric screwdriver allen key bit
1" long surgical tubing
Nut from a surgical tubing gland that happened to have the same thread as..
A handrill minus the chuck and handles
12" of M6 studding
The wire levers removed from 8 clip board clips (Paddle wheel spokes)
Tin from the rim of a chocolate tin (Paddles)
8mm Nylon tubing.
Various M6 nuts and bolts
Cost so far-- I need to replace my hand drill! Have seen one for £6.
Tuesday, 7 June 2011
Footy rescue vessel paddle steamer.
We often sail as a group on ponds where a rescue boat isn't on hand and idealy a dingy of some sort but in the event of getting stuck in the reeds/ radio failure or a sail malfuction just a push from a powered model would suffice. Also I've always wanted a paddle "steamer" and this is an excuse to build one!

A Murray River Paddle Steamer.
The idea is to build a simple electric paddle driven boat which apart from being a model in it’s own right had a secondary duty of rounding stranded or wayward Footys and pushing them back on course or back to the bank.
I came across in the bottom shed a discarded toy aircraft carrier whose 24” long hull was just too good to pass by (No matter what my teenage son thought! You can’t use that Dad, it’s a toy!) I looked on the web for a suitable boat to build with it
I stumbled on the Aussie Murray river steamers and love there simple no nonsense design and it should look right at home on our muddy ponds!
So far my parts list consists of; one afore mentioned one long plastic toy aircraft carrier, a Soviet made windscreen washer motor from a Russian car, a battery from a cheap pistol drill, a cut down planetary gearbox from an electric screwdriver and a hand brace!
I’ve cut the hull down to about half it’s height, cutting off all the odd aircraft carrier deck extensions, this leaves a shallow hull that is approximately right for my paddle steamer. A floating hull in half an hour can’t be bad!
The motor looks tough and very well made I’m not sure how it’ll stand up to continuous running though it doesn’t appear to get hot. I’ll put it on a power supply tomorrow to see exactly how much current it is drawing. With the cut down screwdriver gearbox clamped in the jaws of the hand drill’s chuck propels the handle around at about 60 RPM. These gears will turn the power 90 degrees onto the paddle shaft. I’ll keep you updated!

A Murray River Paddle Steamer.The idea is to build a simple electric paddle driven boat which apart from being a model in it’s own right had a secondary duty of rounding stranded or wayward Footys and pushing them back on course or back to the bank.
I came across in the bottom shed a discarded toy aircraft carrier whose 24” long hull was just too good to pass by (No matter what my teenage son thought! You can’t use that Dad, it’s a toy!) I looked on the web for a suitable boat to build with it
I stumbled on the Aussie Murray river steamers and love there simple no nonsense design and it should look right at home on our muddy ponds!
So far my parts list consists of; one afore mentioned one long plastic toy aircraft carrier, a Soviet made windscreen washer motor from a Russian car, a battery from a cheap pistol drill, a cut down planetary gearbox from an electric screwdriver and a hand brace!
I’ve cut the hull down to about half it’s height, cutting off all the odd aircraft carrier deck extensions, this leaves a shallow hull that is approximately right for my paddle steamer. A floating hull in half an hour can’t be bad!
The motor looks tough and very well made I’m not sure how it’ll stand up to continuous running though it doesn’t appear to get hot. I’ll put it on a power supply tomorrow to see exactly how much current it is drawing. With the cut down screwdriver gearbox clamped in the jaws of the hand drill’s chuck propels the handle around at about 60 RPM. These gears will turn the power 90 degrees onto the paddle shaft. I’ll keep you updated!
Subscribe to:
Posts (Atom)


